Added Touch fix 2
This commit is contained in:
+43
-1
@@ -10,6 +10,7 @@
|
||||
| [T-Deck_UnitTest_241004.bin](./T-Deck_UnitTest_241004.bin) | [T-Deck/T-Deck-Plus function test firmware][1] |
|
||||
| [firmware.meshtastic.factory.v2.5.8-pset-gps.bin](./firmware.meshtastic.factory.v2.5.8-pset-gps.bin) | [T-Deck/T-Deck-Plus factory firmware][2] |
|
||||
| [T-Deck-Plus-TouchFix_241025.bin](./T-Deck-Plus-TouchFix_241025.bin) | [T-Deck-Plus Touch Fix][2] |
|
||||
| [T-Deck-Plus-TouchFix_241203.bin](./T-Deck-Plus-TouchFix_241203.bin) | [T-Deck-Plus Touch Fix][2] |
|
||||
|
||||
⚠⚠⚠
|
||||
|
||||
@@ -88,4 +89,45 @@ esptool --chip esp32c3 --baud 921600 --before default_reset --after hard_reset
|
||||
|
||||
- T-Keyboard the programming and burning interface of ESP32C3 is located at the 6Pin header on the side of the RST button, and the order starts from the top of the RST button, which are 3V3, GND, RST, BOOT, RX, TX, You need to connect USB TO TTL externally to burn the keyboard firmware. For TTL without automatic download circuit, before powering on, short-circuit the BOOT Pin and GND, and then power on. At this time, T-Keyboard will enter the download mode. After the burning is completed, you need to disconnect GND and BOOT before running the program.
|
||||
|
||||

|
||||

|
||||
|
||||
|
||||
## Touch Fix firmware
|
||||
|
||||
- Used to try to repair the touch when the touch does not work properly. If the hardware is not damaged, then open the serial after writing, you should be able to see the following log, slide your finger on the touch screen, and you can see the output sliding coordinates
|
||||
|
||||
```bash
|
||||
|
||||
ESP-ROM:esp32s3-20210327
|
||||
Build:Mar 27 2021
|
||||
rst:0x15 (USB_UART_CHIP_RESET),boot:0x8 (SPI_FAST_FLASH_BOOT)
|
||||
Saved PC:0x420247ee
|
||||
SPIWP:0xee
|
||||
mode:DIO, clock div:1
|
||||
load:0x3fce3808,len:0x44c
|
||||
load:0x403c9700,len:0xbe4
|
||||
load:0x403cc700,len:0x2a38
|
||||
entry 0x403c98d4
|
||||
[ 88][I][esp32-hal-psram.c:96] psramInit(): PSRAM enabled
|
||||
[ 94][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=18 scl=8 freq=100000
|
||||
[ 94][I][SensorCommon.tpp:65] begin(): Using Arduino Wire interface.
|
||||
[ 97][W][Wire.cpp:301] begin(): Bus already started in Master Mode.
|
||||
[ 104][D][TouchDrvGT911.hpp:584] initImpl(): Probe address ....
|
||||
[ 112][D][TouchDrvGT911.hpp:588] initImpl(): Probe address is : 0x5D
|
||||
[ 138][I][TouchDrvGT911.hpp:644] initImpl(): Product id:911
|
||||
[ 138][D][TouchDrvGT911.hpp:653] initImpl(): Current version char :41
|
||||
[ 256][D][TouchDrvGT911.hpp:659] initImpl(): WriteConfig version char :0
|
||||
[ 257][I][TouchDrvGT911.hpp:666] initImpl(): Firmware version: 0x1060
|
||||
[ 260][I][TouchDrvGT911.hpp:668] initImpl(): Resolution : X = 240 Y = 320
|
||||
[ 265][I][TouchDrvGT911.hpp:669] initImpl(): Vendor id:57
|
||||
[ 270][I][TouchDrvGT911.hpp:670] initImpl(): Refresh Rate:10 ms
|
||||
[ 276][I][TouchDrvGT911.hpp:671] initImpl(): MaxTouchPoint:5
|
||||
[ 282][I][TouchDrvGT911.hpp:680] initImpl(): Interrupt Mode: FALLING
|
||||
Init GT911 Sensor success!
|
||||
Pressed!
|
||||
2093ms X[0]:86 Y[0]:152
|
||||
Pressed!
|
||||
2198ms X[0]:86 Y[0]:152
|
||||
Pressed!
|
||||
|
||||
```
|
||||
|
||||
Binary file not shown.
Reference in New Issue
Block a user