Update README

This commit is contained in:
lewishe
2023-12-11 11:35:18 +08:00
parent 6a73a95bfd
commit a1a2cc8464
4 changed files with 13 additions and 15 deletions
+13 -15
View File
@@ -36,27 +36,25 @@ examples
1. Install [ArduinoIDE](https://www.arduino.cc/en/software)
2. Copy all the folders in the `T-Deck/lib` directory to `<C:\Users\UserName\Documents\Arduino\libraries>`. If there is no `libraries` directory, please create a new one. Please note that you are not copying the `lib` directory, but copying the folders in the lib directory
3. Open ArduinoIDE -> Tools
- Board -> ESP32S3 Dev Module
- USB CDC On Boot -> Enable ## Note that you need to change Enable to Disable when USB is not connected, so USB CDC will not prevent the board from starting
- CPU Frequency -> 240MHz
- USB DFU On Boot -> Disable
- Flash Mode -> QIO 80MHz
- Flash Size -> 16MB(128Mb)
- USB Firmware MSC On Boot -> Disable
- PSRAM -> OPI PSRAM
- Partition Scheme -> 16M Flash(3MB APP/9.9MB FATFS)
- USB Mode -> Hardware CDC and JIAG
- Upload Mode -> UART0/Hardware CDC
- Upload Speed -> 921600
3. Open ArduinoIDE ,`Tools` , Look at the picture to choose
| T-Deck(ESP32S3) | T-Keyboard(ESP32C3) |
| -------------------- | -------------------- |
| ![s3](images/s3.jpg) | ![c3](images/c3.jpg) |
4. Insert USB into the PC and click Upload <If the upload fails, keep pressing the BOOT button, click RST, and then click Upload. When the upload is complete, click RST to exit the download mode>
## 3️⃣ Tips:
1. If a microphone is used, the GPIOO button cannot be used
2. If the sketch cannot be uploaded, then you need to press down the middle of the trackball, and then insert the USB, this means the chip is in the download mode, and then click to upload the sketch.
3. The programming and burning interface of ESP32C3 is located at the 6Pin header on the side of the RST button, and the order starts from the top of the RST button, which are 3V3, GND, RST, BOOT, RX, TX
4. If you need to modify the keyboard firmware, please select TTGO T-OI as the board to be programmed on ArduinoIDE
3. T-Keyboard the programming and burning interface of ESP32C3 is located at the 6Pin header on the side of the RST button, and the order starts from the top of the RST button, which are 3V3, GND, RST, BOOT, RX, TX, You need to connect USB TO TTL externally to burn the keyboard firmware. For TTL without automatic download circuit, before powering on, short-circuit the BOOT Pin and GND, and then power on. At this time, T-Keyboard will enter the download mode. After the burning is completed, you need to disconnect GND and BOOT before running the program.
![c3_boot](images/c3_boot.jpg)
4. T-Deck can't upload any sketch,Please enter the upload mode manually.
1. Connect the board via the USB cable
2. Press and hold the BOOT button , While still pressing the BOOT(On the trackball above the keyboard, press down) button
3. Press RST button
4. Release the RST button
5. Release the BOOT button (If there is no BOOT button, disconnect IO0 from GND.)
6. Upload sketch
## 4️⃣ Where to buy:
BIN
View File
Binary file not shown.

After

Width:  |  Height:  |  Size: 59 KiB

Binary file not shown.

After

Width:  |  Height:  |  Size: 20 KiB

BIN
View File
Binary file not shown.

After

Width:  |  Height:  |  Size: 74 KiB