first commit
This commit is contained in:
@@ -0,0 +1,87 @@
|
||||
/*
|
||||
* A demo of a simple AceButton used to handle the events from one button.
|
||||
* Pretty much the same as SingleButton.ino example but the button is wired with
|
||||
* an external pull-down resistor, instead of using the built-in pull-up
|
||||
* resistor.
|
||||
*/
|
||||
|
||||
#include <AceButton.h>
|
||||
using namespace ace_button;
|
||||
|
||||
// The pin number attached to the button.
|
||||
const int BUTTON_PIN = 7;
|
||||
|
||||
#ifdef ESP32
|
||||
// Different ESP32 boards use different pins
|
||||
const int LED_PIN = 2;
|
||||
#else
|
||||
const int LED_PIN = LED_BUILTIN;
|
||||
#endif
|
||||
|
||||
// LED states. Some microcontrollers wire their built-in LED the reverse.
|
||||
const int LED_ON = HIGH;
|
||||
const int LED_OFF = LOW;
|
||||
|
||||
// Automatically uses the default ButtonConfig. We will configure this later
|
||||
// using AceButton::init() method in setup() below.
|
||||
AceButton button;
|
||||
|
||||
void handleEvent(AceButton*, uint8_t, uint8_t);
|
||||
|
||||
void setup() {
|
||||
delay(1000); // some microcontrollers reboot twice
|
||||
Serial.begin(115200);
|
||||
while (! Serial); // Wait until Serial is ready - Leonardo/Micro
|
||||
Serial.println(F("setup(): begin"));
|
||||
|
||||
// initialize built-in LED as an output
|
||||
pinMode(LED_PIN, OUTPUT);
|
||||
|
||||
// Button uses an external 10k resistor.
|
||||
pinMode(BUTTON_PIN, INPUT);
|
||||
|
||||
// We use the AceButton::init() method here instead of using the constructor
|
||||
// to show an alternative. Using init() allows the configuration of the
|
||||
// hardware pin and the button to be placed closer to each other.
|
||||
button.init(BUTTON_PIN, LOW);
|
||||
|
||||
// Configure the ButtonConfig with the event handler, and enable the LongPress
|
||||
// and RepeatPress events which are turned off by default.
|
||||
ButtonConfig* buttonConfig = button.getButtonConfig();
|
||||
buttonConfig->setEventHandler(handleEvent);
|
||||
buttonConfig->setFeature(ButtonConfig::kFeatureClick);
|
||||
buttonConfig->setFeature(ButtonConfig::kFeatureDoubleClick);
|
||||
buttonConfig->setFeature(ButtonConfig::kFeatureLongPress);
|
||||
buttonConfig->setFeature(ButtonConfig::kFeatureRepeatPress);
|
||||
|
||||
Serial.println(F("setup(): ready"));
|
||||
}
|
||||
|
||||
void loop() {
|
||||
// Should be called every 20ms or faster for the default debouncing time
|
||||
// of ~50ms.
|
||||
button.check();
|
||||
}
|
||||
|
||||
// The event handler for the button.
|
||||
void handleEvent(AceButton* /* button */, uint8_t eventType,
|
||||
uint8_t buttonState) {
|
||||
|
||||
// Print out a message for all events.
|
||||
Serial.print(F("handleEvent(): eventType: "));
|
||||
Serial.print(eventType);
|
||||
Serial.print(F("; buttonState: "));
|
||||
Serial.println(buttonState);
|
||||
|
||||
// Control the LED only for the Pressed and Released events.
|
||||
// Notice that if the MCU is rebooted while the button is pressed down, no
|
||||
// event is triggered and the LED remains off.
|
||||
switch (eventType) {
|
||||
case AceButton::kEventReleased:
|
||||
digitalWrite(LED_PIN, LED_ON);
|
||||
break;
|
||||
case AceButton::kEventPressed:
|
||||
digitalWrite(LED_PIN, LED_OFF);
|
||||
break;
|
||||
}
|
||||
}
|
||||
Reference in New Issue
Block a user