/** * * @license MIT License * * Copyright (c) 2022 lewis he * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell * copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in all * copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE * SOFTWARE. * * @file QMI8658_WakeOnMotionCallBack.ino * @author Lewis He (lewishe@outlook.com) * @date 2022-11-07 * */ #include #include #include #include "SensorQMI8658.hpp" // #define USE_WIRE #ifndef SENSOR_SDA #define SENSOR_SDA 17 #endif #ifndef SENSOR_SCL #define SENSOR_SCL 18 #endif #ifndef SENSOR_IRQ #define SENSOR_IRQ -1 #endif SensorQMI8658 qmi; IMUdata acc; IMUdata gyr; bool interruptFlag = false; void setFlag(void) { interruptFlag = true; } void wakeUp() { Serial.println("Awake!"); } void setup() { Serial.begin(115200); while (!Serial); #ifdef USE_WIRE //Using WIRE !! if (!qmi.begin(Wire, QMI8658_L_SLAVE_ADDRESS, SENSOR_SDA, SENSOR_SCL)) { Serial.println("Failed to find QMI8658 - check your wiring!"); while (1) { delay(1000); } } #else #ifndef CONFIG_IDF_TARGET_ESP32 //Use tbeams3 defalut spi pinz #define SPI_MOSI (35) #define SPI_SCK (36) #define SPI_MISO (37) #define SPI_CS (47) #define IMU_CS (34) #define IMU_INT1 (33) //INTERRUPT PIN1 & PIN2 ,Use or logic to form a pin pinMode(SPI_CS, OUTPUT); //sdcard pin set high digitalWrite(SPI_CS, HIGH); if (!qmi.begin(IMU_CS, SPI_MOSI, SPI_MISO, SPI_SCK)) { #else //Use esp32dev module defalut spi pin #define IMU_CS (5) #define IMU_INT1 (15) #define IMU_INT2 (22) if (!qmi.begin(IMU_CS)) { #endif Serial.println("Failed to find QMI8658 - check your wiring!"); while (1) { delay(1000); } } #endif /* Get chip id*/ Serial.print("Device ID:"); Serial.println(qmi.getChipID(), HEX); // enabling wake on motion low power mode with a threshold of 200 mg and // an accelerometer data rate of 128 Hz. qmi.configWakeOnMotion(); qmi.setWakeupMotionEventCallBack(wakeUp); /* * When the QMI8658 is configured as Wom, the interrupt level is arbitrary, * not absolute high or low, and it is in the jump transition state */ pinMode(IMU_INT1, INPUT_PULLUP); #ifdef IMU_INT2 pinMode(IMU_INT2, INPUT_PULLUP); attachInterrupt(IMU_INT2, setFlag, CHANGE); #else attachInterrupt(IMU_INT1, setFlag, CHANGE); #endif // Print register configuration information qmi.dumpCtrlRegister(); } void loop() { if (interruptFlag) { interruptFlag = false; qmi.readSensorStatus(); } }