Root cause (on device): sound_engine zero-initialized i2s_pin_config_t, leaving mck_io_num == 0. i2s_set_pin() then claimed GPIO0 — an MCLK-capable pin on the S3 and the trackball centre / BOOT line — as its MCLK output. Verified on device with a diagnostic build: pin0 read LOW at idle, exactly one latched FALLING edge, clicks never registered. - sound_engine: set pins.mck_io_num = I2S_PIN_NO_CHANGE explicitly. - NetDeck: register the trackball click on release with contact-bounce collapse (the proven CrtTerminal pattern); pollTouch re-arms when isPressed() stays true but getPoint() reports no points (stuck GT911 IRQ on some units). - Emulator parity (so this class of bug dies before flashing): GPIO-matrix pin-ownership model in the shim — i2s_set_pin() claims its pins, claimed pins are dead inputs (digitalRead LOW, no edges, loud WARNING on claim/ISR collisions); host pin writes go through emu::setPin/togglePin with an edge-accurate ISR latch (a full press+release pulse between dispatches no longer gets swallowed); E2E inits SDL_INIT_AUDIO so the I2S path actually runs there. Regression coverage: e2e/trackball_click (fails on the old engine), unit/shim_claimed_pin_is_dead_input, unit/shim_edge_survives_same_dispatch_pulse. - Makefile: firmware step follows the sketch move (root platformio.ini, src_dir = src/netdeck). - HW.md: new notes file for emulator-vs-hardware quirks and the on-device debugging recipe. On-device verified: clicks register in both views (beacon drops, node routing). Fast layer 23 unit + 7 integration green. Note: e2e boot_and_controls + network_journey failures are pre-existing at HEAD (reproduced on a clean stash before this change).
39 lines
1022 B
C++
39 lines
1022 B
C++
/**
|
|
* @file shim_globals.cpp
|
|
* @brief Definitions of the shim globals that src/main.cpp normally owns.
|
|
*
|
|
* Both test binaries (NetDeck-tests, NetDeck-e2e) link this instead of
|
|
* main.cpp, so they get the shim environment without the SDL window/event
|
|
* host loop. The sketch itself is included by each test's own TU (single-TU
|
|
* inclusion, same trick main.cpp uses).
|
|
*/
|
|
#include "Arduino.h"
|
|
#include "TFT_eSPI.h"
|
|
#include "Wire.h"
|
|
#include "SPI.h"
|
|
|
|
namespace emu {
|
|
uint8_t pinLevels[64];
|
|
const char *pinDrivenBy[64];
|
|
std::deque<PinEdge> pinEdges;
|
|
bool touchDown = false;
|
|
int touchX = 0, touchY = 0;
|
|
std::deque<uint8_t> keyboard;
|
|
bool quitRequested = false;
|
|
} // namespace emu
|
|
|
|
namespace emuGfx {
|
|
uint32_t fb[320 * 240];
|
|
SDL_Texture *tex = nullptr;
|
|
bool dirty = true;
|
|
} // namespace emuGfx
|
|
|
|
SerialSim Serial;
|
|
TwoWire Wire;
|
|
SPIClass SPI;
|
|
|
|
const FreeFontStub FreeSansBold24pt7b {0};
|
|
const FreeFontStub FreeSansBold18pt7b {0};
|
|
const FreeFontStub FreeSansOblique12pt7b {0};
|
|
const FreeFontStub FreeSans12pt7b {0};
|