Files
lilygo-t-deck/lib/Arduino_GFX/src/display/Arduino_R61529.h
T
2024-09-19 11:13:25 +08:00

286 lines
10 KiB
C++
Raw Blame History

This file contains ambiguous Unicode characters
This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.
/*
* start rewrite from:
* https://github.com/adafruit/Adafruit-GFX-Library.git
* https://github.com/daumemo/IPS_LCD_R61529_FT6236_Arduino_eSPI_Test
* Data Sheet:
* http://read.pudn.com/downloads648/ebook/2620902/R61529.pdf
*/
#ifndef _ARDUINO_R61529_H_
#define _ARDUINO_R61529_H_
#include <Arduino.h>
#include <Print.h>
#include "../Arduino_GFX.h"
#include "../Arduino_TFT.h"
#define R61529_TFTWIDTH 320 // R61529 max width
#define R61529_TFTHEIGHT 480 // R61529 max height
#define R61529_RST_DELAY 20 // delay ms wait for reset finish
#define R61529_SLPIN_DELAY 20 // delay ms wait for sleep in finish
#define R61529_SLPOUT_DELAY 200 // delay ms wait for sleep out finish
// User Command
#define R61529_NOP 0x00 // nop
#define R61529_SWRESET 0x01 // soft_reset
#define R61529_RDDID 0x04 // read_DDB_start
#define R61529_RDMODE 0x0A // get_power_mode
#define R61529_RDMADCTL 0x0B // get_address_mode
#define R61529_RDPIXFMT 0x0C // get_pixel_format
#define R61529_RDIMGFMT 0x0D // get_display_mode
#define R61529_RDSIGMODE 0x0E // get_signal_mode
#define R61529_RDSELFDIAG 0x0F // get_diagnostic_result
#define R61529_SLPIN 0x10 // enter_sleep_mode
#define R61529_SLPOUT 0x11 // exit_sleep_mode
#define R61529_PTLON 0x12 // enter_partial_mode
#define R61529_NORON 0x13 // enter_normal_mode
#define R61529_INVOFF 0x20 // exit_invert_mode
#define R61529_INVON 0x21 // enter_invert_mode
#define R61529_DISPOFF 0x28 // set_display_off
#define R61529_DISPON 0x29 // set_display_on
#define R61529_CASET 0x2A // set_column_address
#define R61529_PASET 0x2B // set_page_address
#define R61529_RAMWR 0x2C // write_memory_start
#define R61529_RAMRD 0x2E // read_memory_start
#define R61529_PTLAR 0x30 // set_partial_area
#define R61529_TEAROFF 0x34 // set_tear_off
#define R61529_TEARON 0x35 // set_tear_on
#define R61529_MADCTL 0x36 // set_address_mode
#define R61529_IDLEOFF 0x38 // exit_idle_mode
#define R61529_IDLEON 0x39 // enter_idle_mode
#define R61529_PIXFMT 0x3A // set_pixel_format
#define R61529_WRMC 0x3C // write_memory_continue
#define R61529_RDMC 0x3E // read_memory_continue
#define R61529_SETTSL 0x44 // set_tear_scanline
#define R61529_GETSL 0x45 // get_scanline
#define R61529_RDDDBS 0xA1 // read_DDB_start
#define R61529_MCAP 0xB0 // Manufacturer Command Access Protect
#define R61529_LPMC 0xB1 // Low Power Mode Control
#define R61529_FMAIS 0xB3 // Frame Memory Access and Interface Setting
#define R61529_DISPMODE 0xB4 // Display Mode
#define R61529_RCEEC 0xB5 // Read Checksum and ECC Error Count
#define R61529_DSICTL 0xB6 // DSI Control
#define R61529_MDDICTL 0xB7 // MDDI Control
#define R61529_BLCTL1 0xB8 // Backlight Control (1)
#define R61529_BLCTL2 0xB9 // Backlight Control (2)
#define R61529_BLCTL3 0xBA // Backlight Control (3)
#define R61529_DCRD 0xBF // Device Code Read
#define R61529_PDS 0xC0 // Panel Driving Setting
#define R61529_DTSFNM 0xC1 // Display Timing Setting for Normal Mode
#define R61529_TESTMODE1 0xC3 // Test Mode 1
#define R61529_SGDTS 0xC4 // Source/Gate Driving Timing Setting
#define R61529_DPIPCTL 0xC6 // DPI Polarity Control
#define R61529_TESTMODE2 0xC7 // Test Mode 2
#define R61529_GAMMASETA 0xC8 // Gamma Setting A Set
#define R61529_GAMMASETB 0xC9 // Gamma Setting B Set
#define R61529_GAMMASETC 0xCA // Gamma Setting C Set
#define R61529_TESTMODE3 0xCC // Test Mode 3
#define R61529_PWSET 0xD0 // Power Setting (Charge Pump Setting)
#define R61529_VCOMSET 0xD1 // VCOM Setting
#define R61529_TESTMODE4 0xD6 // Test Mode 4
#define R61529_TESTMODE5 0xD7 // Test Mode 5
#define R61529_TESTMODE6 0xD8 // Test Mode 6
#define R61529_TESTMODE7 0xD9 // Test Mode 7
#define R61529_TESTMODE8 0xDA // Test Mode 8
#define R61529_NVMAC 0xE0 // NVM Access Control
#define R61529_SETDDBWRCTL 0xE1 // set_DDB_write_control
#define R61529_NVMLC 0xE2 // NVM Load Control
#define R61529_TESTMODE9 0xE4 // Test Mode 9
#define R61529_TESTMODE10 0xE5 // Test Mode 10
#define R61529_TESTMODE11 0xE6 // Test Mode 11
#define R61529_TESTMODE12 0xE7 // Test Mode 12
#define R61529_TESTMODE13 0xF3 // Test Mode 13
#define R61529_RDMODEIN 0xF5 // Read Mode In for DBI Only
#define R61529_RDMODEOUT 0xF6 // Read Mode Out for DBI Only
#define R61529_TESTMODE14 0xF8 // Test Mode 14
#define R61529_TESTMODE15 0xFA // Test Mode 15
#define R61529_TESTMODE16 0xFC // Test Mode 16
#define R61529_TESTMODE17 0xFD // Test Mode 17
#define R61529_TESTMODE18 0xFE // Test Mode 18
// parameters
#define R61529_MADCTL_MY 0x80 // Bottom to top
#define R61529_MADCTL_MX 0x40 // Right to left
#define R61529_MADCTL_MV 0x20 // Reverse Mode
#define R61529_MADCTL_ML 0x10 // LCD refresh Bottom to top
#define R61529_MADCTL_RGB 0x00 // Red-Green-Blue pixel order
#define R61529_MADCTL_BGR 0x08 // Blue-Green-Red pixel order
#define R61529_MADCTL_MH 0x04 // LCD refresh right to left
#define R61529_MADCTL_SS 0x02
#define R61529_MADCTL_GS 0x01
static const uint8_t r61529_init_operations[] = {
BEGIN_WRITE,
WRITE_COMMAND_8, R61529_SLPOUT,
END_WRITE,
DELAY, R61529_SLPOUT_DELAY,
BEGIN_WRITE,
WRITE_C8_D8, R61529_MCAP, 0x04,
WRITE_COMMAND_8, R61529_BLCTL1, // lcd pwm
WRITE_BYTES, 20,
0x02, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00,
WRITE_COMMAND_8, R61529_BLCTL2, // lcd pwm
WRITE_BYTES, 4,
0x01, // PWMON = 1;
0x00, // BDCV = 255;
0xff, // pwm freq = 13.7 kHz
0x18, // PWMWM = 1; LEDPWME = 1;
// additional commands:
WRITE_COMMAND_8, R61529_FMAIS, // Frame Memory Access and Interface Setting
WRITE_BYTES, 5,
0x02, // reset start position of a window area address...
0x00, // TE pin is used. TE signal is output every frame.
0x00, // empty according to the datasheet - does nothing;
0x00, // convert 16/18 bits to 24bits data by writing zeroes to LSBs. Sets image data write/read format(?)
0x00, // ???? (not needed?)
END_WRITE,
DELAY, 2,
BEGIN_WRITE,
WRITE_C8_D8, R61529_DISPMODE, 0x00, // Display Mode, Uses internal oscillator
WRITE_COMMAND_8, R61529_PDS, // Panel Driving Setting;
WRITE_BYTES, 8,
0x03, // Output polarity is inverted. Left/right interchanging scan. Forward scan. BGR mode (depends on other settings). S960 → S1 (depends)
0xDF, // Number of lines for driver to drive - 480.
0x40, // Scan start position - Gate1. (depend on other param);
0x10, // Dot inversion. Dot inversion in not-lit display area. If 0x13 - both will be set to 'column inversion'.
0x00, // settings for non-lit display area...
0x01, // 3 frame scan interval in non-display area...
0x00, // Source output level in retrace period...
0x55, // 54 . Internal clock divider = 5 (low and high periods).
WRITE_COMMAND_8, R61529_DTSFNM, // Display Timing Setting for Normal Mode
WRITE_BYTES, 5,
0x07, // Clock devider = 12. 14MHz/12. Used by display circuit and step-up circuit.
0x27, // These bits set the number of clocks in 1 line period. 0x27 - 39 clocks.
0x08, // Number of back porch lines. 0x08 - 8 lines.
0x08, // Number of front porch lines. 0x08 - 8lines.
0x00, // Spacial configuriation mode 1 (?). 1 line inversion mode (?).
WRITE_COMMAND_8, R61529_SGDTS, // Source/Gate Driving Timing Setting
WRITE_BYTES, 4,
0x57, // falling position (stop) of gate driver - 4 clocks... gate start position - 8 clocks...
0x00, // nothing to set up according to the datasheet
0x05, // Source precharge period (GND) - 5 clocks.
0x03, // source precharge period (VCI) - 3 clocks.
WRITE_C8_D8, R61529_DPIPCTL, 0x04, // DPI polarity control, VSYNC -Active Low. HSYNC - Active Low. DE pin enable data write in when DE=1. Reads data on the rising edge of the PCLK signal.
//----Gamma setting start-----
WRITE_COMMAND_8, R61529_GAMMASETA,
WRITE_BYTES, 24,
0x03, 0x12, 0x1A, 0x24,
0x32, 0x4B, 0x3B, 0x29,
0x1F, 0x18, 0x12, 0x04,
0x03, 0x12, 0x1A, 0x24,
0x32, 0x4B, 0x3B, 0x29,
0x1F, 0x18, 0x12, 0x04,
WRITE_COMMAND_8, R61529_GAMMASETB,
WRITE_BYTES, 24,
0x03, 0x12, 0x1A, 0x24,
0x32, 0x4B, 0x3B, 0x29,
0x1F, 0x18, 0x12, 0x04,
0x03, 0x12, 0x1A, 0x24,
0x32, 0x4B, 0x3B, 0x29,
0x1F, 0x18, 0x12, 0x04,
WRITE_COMMAND_8, R61529_GAMMASETC,
WRITE_BYTES, 24,
0x03, 0x12, 0x1A, 0x24,
0x32, 0x4B, 0x3B, 0x29,
0x1F, 0x18, 0x12, 0x04,
0x03, 0x12, 0x1A, 0x24,
0x32, 0x4B, 0x3B, 0x29,
0x1F, 0x18, 0x12, 0x04,
//---Gamma setting end--------
// old ones:
WRITE_COMMAND_8, R61529_PWSET,
WRITE_BYTES, 16,
0x99, // DC4~1//A5. Set up clock cycle of the internal step up controller.
0x06, // BT // Set Voltage step up factor.
0x08, // default according to the datasheet - does nothing.
0x20, // VCN step up cycles.
0x29, // VC1, VC2// VCI3 voltage = 2.70V; VCI2 voltage = 3.8V.
0x04, // default
0x01, // default
0x00, // default
0x08, // default
0x01, // default
0x00, // default
0x06, // default
0x01, // default
0x00, // default
0x00, // default
0x20, // default
WRITE_COMMAND_8, R61529_VCOMSET, // VCOM setting
WRITE_BYTES, 4,
0x00, // disable write to VDC[7:0]
0x20, // 45 38 VPLVL// voltage of γ correction registers for positive polarity
0x20, // 45 38 VNLVL// voltage of γ correction registers for negative polarity
0x15, // 32 2A VCOMDC// VNLVL x 0.063
WRITE_COMMAND_8, R61529_NVMAC, // NVM Access Control
WRITE_BYTES, 3,
0x00, // NVM access is disabled
0x00, // Erase operation (disabled).
0x00, // TE pin works as tearing effect pin.
// should be one more writeData(0x00}, according to the datasheet.
WRITE_COMMAND_8, R61529_SETDDBWRCTL, // set_DDB_write_control
WRITE_BYTES, 6,
0x00, 0x00, 0x00, 0x00,
0x00, 0x00,
WRITE_C8_D8, R61529_NVMLC, 0x00, // NVM Load Control, does not execute data load from the NVM to each command
WRITE_C8_D8, 0x3A, 0x55, // set_pixel_format, 16-Bit/pixel = 55h, 24-bit/pixel = 77h
WRITE_COMMAND_8, R61529_DISPON,
END_WRITE,
DELAY, 20};
class Arduino_R61529 : public Arduino_TFT
{
public:
Arduino_R61529(Arduino_DataBus *bus, int8_t rst = GFX_NOT_DEFINED, uint8_t r = 0, bool ips = false);
bool begin(int32_t speed = GFX_NOT_DEFINED) override;
void writeAddrWindow(int16_t x, int16_t y, uint16_t w, uint16_t h) override;
void setRotation(uint8_t r) override;
void invertDisplay(bool) override;
void displayOn() override;
void displayOff() override;
protected:
void tftInit() override;
private:
};
#endif