7.2 KiB
7.2 KiB
ESP_IDF_TouchDrv_Example
The current example only writes the CSTxxx series touch application.
The other sensors have not been added, but the methods are the same.
Configure the Project
Open the project configuration menu (idf.py menuconfig).
In the SensorLib Example Configuration menu:
- Select the PMU Type in the
SensorLib read and write methodsoption,Choose according to the situation- Implemented using built-in read and write methods (Read and write methods are provided internally by SensorLib, supporting high version esp-idf >= 5.0, and low version methods (< 5.0))
- Implemented using read and write callback methods (Implemented using externally provided methods, suitable for multiple platforms)
- In
Sensor SCL GPIO Numselect the clock pin to connect to the PMU,the default is 17 - In
Sensor SDA GPIO Numselect the data pin connected to the PMU,the default is 18 - Select the interrupt pin connected to the PMU in
Sensor Interrupt Pin, the default is 16 - Select
Sensor reset Pin, the default is 21 Master FrequencyThe maximum communication frequency defaults to 100000HZ, and you can decide whether to change it according to the situation.
How to Use Example
Before project configuration and build, be sure to set the correct chip target using idf.py set-target <chip_name>. default use esp32s3
Build and Flash
Run idf.py -p PORT flash monitor to build, flash and monitor the project.
(To exit the serial monitor, type Ctrl-].)
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
Example Output
The output information is to configure the output voltage and enable status of the PMU
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x15 (USB_UART_CHIP_RESET),boot:0xa (SPI_FAST_FLASH_BOOT)
Saved PC:0x403788f6
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3810,len:0x178c
load:0x403c9700,len:0x4
load:0x403c9704,len:0xbfc
load:0x403cc700,len:0x2d64
entry 0x403c9900
I (26) boot: ESP-IDF v5.3-dev-1288-g5524b692ee 2nd stage bootloader
I (27) boot: compile time Jan 10 2024 22:49:17
I (27) boot: Multicore bootloader
I (31) boot: chip revision: v0.2
I (35) boot.esp32s3: Boot SPI Speed : 80MHz
I (40) boot.esp32s3: SPI Mode : DIO
I (45) boot.esp32s3: SPI Flash Size : 2MB
I (49) boot: Enabling RNG early entropy source...
I (55) boot: Partition Table:
I (58) boot: ## Label Usage Type ST Offset Length
I (66) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (73) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (81) boot: 2 factory factory app 00 00 00010000 00100000
I (88) boot: End of partition table
I (92) esp_image: segment 0: paddr=00010020 vaddr=3c020020 size=0e0dch ( 57564) map
I (111) esp_image: segment 1: paddr=0001e104 vaddr=3fc93100 size=01f14h ( 7956) load
I (113) esp_image: segment 2: paddr=00020020 vaddr=42000020 size=1acb0h (109744) map
I (137) esp_image: segment 3: paddr=0003acd8 vaddr=3fc95014 size=00994h ( 2452) load
I (138) esp_image: segment 4: paddr=0003b674 vaddr=40374000 size=0f0e0h ( 61664) load
I (163) boot: Loaded app from partition at offset 0x10000
I (163) boot: Disabling RNG early entropy source...
I (163) cpu_start: Multicore app
I (176) cpu_start: Pro cpu start user code
I (176) cpu_start: cpu freq: 240000000 Hz
I (177) cpu_start: Application information:
I (177) cpu_start: Project name: ESP_IDF_TouchDrv_Example
I (177) cpu_start: App version: v0.1.4-6-gfeaf675-dirty
I (177) cpu_start: Compile time: Jan 11 2024 14:01:31
I (177) cpu_start: ELF file SHA256: 3ce1527fc...
I (178) cpu_start: ESP-IDF: v5.3-dev-1288-g5524b692ee
I (178) cpu_start: Min chip rev: v0.0
I (178) cpu_start: Max chip rev: v0.99
I (178) cpu_start: Chip rev: v0.2
I (178) heap_init: Initializing. RAM available for dynamic allocation:
I (179) heap_init: At 3FC96290 len 00053480 (333 KiB): RAM
I (179) heap_init: At 3FCE9710 len 00005724 (21 KiB): RAM
I (179) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM
I (180) heap_init: At 600FE010 len 00001FD8 (7 KiB): RTCRAM
I (181) spi_flash: detected chip: winbond
I (181) spi_flash: flash io: dio
W (181) spi_flash: Detected size(16384k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
W (181) i2c: This driver is an old driver, please migrate your application code to adapt `driver/i2c_master.h`
I (182) sleep: Configure to isolate all GPIO pins in sleep state
I (182) sleep: Enable automatic switching of GPIO sleep configuration
I (183) main_task: Started on CPU0
I (193) main_task: Calling app_main()
I (193) gpio: GPIO[16]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:2
I (193) I2C: Implemented using read and write callback methods (Use lower version < 5.0 API)
I (193) mian: I2C initialized successfully
I (193) TOUCH: ----touch_drv_init----
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- 15 -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
I (303) TOUCH: Find touch address 0x15
I (303) TOUCH: Find touch address 0x15
I (303) TOUCH: Implemented using built-in read and write methods (Use lower version < 5.0 API)
Using ESP-IDF Driver interface.
E (303) i2c: i2c driver install error
I (303) gpio: GPIO[21]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (303) gpio: GPIO[21]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
Chip ID:0xb5
Version :0x2
Touch type:CST816T
I (383) TOUCH: Init touch SUCCESS!
I (383) TOUCH: Some CST816 will automatically enter sleep,can use the touch.disableAutoSleep() to turn off
I (383) gpio: GPIO[21]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (513) mian: Run...
I (513) main_task: Returned from app_main()
X[0]:143 Y[0]:127
X[0]:143 Y[0]:127
X[0]:142 Y[0]:127
X[0]:141 Y[0]:126
X[0]:138 Y[0]:125
X[0]:135 Y[0]:123
X[0]:131 Y[0]:121
X[0]:126 Y[0]:119
X[0]:121 Y[0]:117
X[0]:84 Y[0]:146
X[0]:85 Y[0]:146
X[0]:86 Y[0]:145
X[0]:87 Y[0]:143
X[0]:88 Y[0]:140
X[0]:89 Y[0]:136
X[0]:90 Y[0]:132
X[0]:91 Y[0]:127
X[0]:92 Y[0]:123
X[0]:93 Y[0]:119
X[0]:94 Y[0]:115
X[0]:95 Y[0]:111
I (513563) TOUCH: Touch Home button pressed!
I (513573) TOUCH: Touch Home button pressed!
I (513583) TOUCH: Touch Home button pressed!
I (513603) TOUCH: Touch Home button pressed!
I (513613) TOUCH: Touch Home button pressed!
I (513633) TOUCH: Touch Home button pressed!
I (513643) TOUCH: Touch Home button pressed!
Build process example
Assuming you don't have esp-idf yet
mkdir -p ~/esp
cd ~/esp
git clone --recursive https://github.com/espressif/esp-idf.git
git clone https://github.com/lewisxhe/XPowersLib.git
cd esp-idf
./install.sh
. ./export.sh
cd ..
cd SensorLib/examples/ESP_IDF_Example
Configure SDA,SCL,INT,RST,Pin
...
idf.py menuconfig
idf.py build
idf.py -b 921600 flash
idf.py monitor