Drive radar blips from the T-Deck Plus dual microphones

Add a SoundDetector that reads the ES7210 as a 4-slot TDM stream
(slot 0 = MIC1/left, slot 2 = MIC3/right), tracks a per-channel RMS
envelope with an adaptive noise floor, and publishes a stereo balance
plus a dB-mapped loudness.

The radar sketch now slides a single reused blip left/right from the
balance and moves it nearer as the loudness rises, instead of firing a
hardcoded demo blip. The device's own ping/click mutes the detector for
200 ms so it cannot hear itself.

The trackball stays detached: GPIO0 is unavailable while the ES7210
microphones are running.
This commit is contained in:
Dejvino
2026-11-12 08:20:38 +01:00
parent 7dfdc06e6f
commit 2ba92a65d1
3 changed files with 391 additions and 17 deletions
+54 -17
View File
@@ -31,6 +31,7 @@
#include "utilities.h"
#include "TouchDrvGT911.hpp"
#include "sound_engine.h"
#include "sound_detector.h"
// ---------------------------------------------------------------------------
// Hardware
@@ -38,6 +39,7 @@
TFT_eSPI tft;
TouchDrvGT911 touch;
SoundEngine sound;
SoundDetector soundDetector;
Preferences prefs;
static bool touchAvail = false;
@@ -391,6 +393,8 @@ static void printPrompt()
// ---------------------------------------------------------------------------
static void sndBlip()
{
// Keep the device's own radar ping out of the microphone detector.
soundDetector.suppress(200);
SndEvent e = { SND_TONE, 540, 0, 10, 8000 };
sound.play(e);
delay(15);
@@ -398,6 +402,7 @@ static void sndBlip()
static void sndClick()
{
soundDetector.suppress(200);
SndEvent e = { SND_TONE, 660, 0, 152, 5000 };
sound.play(e);
}
@@ -624,24 +629,43 @@ void initRadar() {
}
}
// Call this when an audio trigger or target is detected
// lrBalance: -1.0 (far left) to +1.0 (far right)
// loudness: mapped to distance (higher volume = closer to origin)
void triggerBlip(float lrBalance, float loudness) {
// Index of the blip currently driven by the microphone. Reused every frame so
// a continuous sound slides around instead of filling all MAX_BLIPS slots.
static int liveBlip = -1;
static int allocBlip() {
for (int i = 0; i < MAX_BLIPS; i++) {
if (!blips[i].active) {
blips[i].active = true;
// Map L/R balance to forward-facing wedge (-45 deg to +45 deg)
blips[i].angle = constrain(lrBalance, -1.0f, 1.0f) * (M_PI / 4.0f);
// Loudness maps to distance: loudest is near origin, quiet is near edge
blips[i].distance = constrain(1.0f - (loudness / 100.0f), 0.15f, 0.95f);
blips[i].alpha = 255;
break;
}
if (!blips[i].active) return i;
}
return -1;
}
// lrBalance: -1.0 (far left) to +1.0 (far right)
// loudness: 0.0 (quiet/far) to 1.0 (loud/near)
static void placeBlip(int i, float lrBalance, float loudness) {
if (i < 0) return;
blips[i].active = true;
// Map L/R balance to forward-facing wedge (-45 deg to +45 deg)
blips[i].angle = constrain(lrBalance, -1.0f, 1.0f) * (M_PI / 4.0f);
// Loudness maps to distance: loudest is near origin, quiet is near edge
blips[i].distance = constrain(1.0f - loudness, 0.15f, 0.95f);
blips[i].alpha = 255;
}
// One-shot blip (manual trigger / future events)
void triggerBlip(float lrBalance, float loudness) {
placeBlip(allocBlip(), lrBalance, loudness);
sndClick();
}
// Continuous update from the dual-microphone detector.
static void updateSoundBlip(float lrBalance, float loudness) {
if (liveBlip < 0 || !blips[liveBlip].active) {
liveBlip = allocBlip();
}
placeBlip(liveBlip, lrBalance, loudness);
}
static void drawArc(float r, uint32_t color) {
for (float a = -M_PI / 4.0; a <= M_PI / 4.0; a += 0.05) {
int ax = RADAR_ORIGIN_X + (int)(r * sin(a));
@@ -687,10 +711,13 @@ void radarUpdate() {
sndBlip();
} else if (sweepAngle < MAX_RADIUS) {
drawArc(sweepAngle, C_GLOW);
}
if (sweepAngle > 109 && sweepAngle < 111) {
triggerBlip(0.2, 50);
}
// Feed the live microphone measurement into the blip layer. Balance moves
// it left/right; loudness pulls it toward the centre (closer target).
SoundReading snd = soundDetector.read();
if (snd.active) {
updateSoundBlip(snd.balance, snd.loudness);
}
// 4. Render Active Target Blips with Phosphor Decay
@@ -1006,7 +1033,11 @@ static void hardwareInit()
Serial.println("No GT911 touch found");
}
attachTrackball();
// NOTE: GPIO0 (trackball centre / BOOT) is unavailable while the ES7210
// microphones are running, and leaving its interrupt enabled causes
// spurious captures. Keep it detached; the microphone radar does not need
// the trackball.
// attachTrackball();
}
static void bootSequence()
@@ -1044,6 +1075,12 @@ void setup()
bootSequence();
initRadar();
if (!soundDetector.begin(16000)) {
Serial.println("Sound detector init failed (ES7210 mics)");
} else {
Serial.println("Sound detector ready (MIC1 left / MIC3 right)");
}
}
void loop()
+280
View File
@@ -0,0 +1,280 @@
/**
* @file sound_detector.cpp
* @brief ES7210 dual-microphone capture + stereo balance/loudness detector.
*
* The T-Deck Plus has two populated MEMS microphones on the ES7210. The codec
* outputs all four ADC channels as a 4-slot TDM stream on SDOUT1:
* slot 0 = MIC1 (left), slot 2 = MIC3 (right)
* We only need slots 0 and 2; slot 1/3 are ignored.
*
* The detector runs in its own FreeRTOS task so the radar loop never blocks on
* I2S. It publishes smoothed, noise-floor-relative levels that the sketch turns
* into a blip angle (balance) and distance (loudness).
*/
#include "sound_detector.h"
#include "utilities.h"
#include "es7210.h"
#include <Wire.h>
#include <math.h>
#define MIC_I2S_PORT I2S_NUM_1
#define MIC_BLOCK_FRAMES 256 // 16 ms at 16 kHz
#define MIC_CHANNELS 4 // 4-slot TDM
#define MIC_SLOT_LEFT 0 // MIC1
#define MIC_SLOT_RIGHT 2 // MIC3
#define MIC_GAIN GAIN_30DB
// Set to 1 to print detected levels while tuning the microphones on hardware.
#ifndef SOUND_DETECTOR_DEBUG
#define SOUND_DETECTOR_DEBUG 0
#endif
// Envelope / detector tuning (per 16 ms block).
static constexpr float ENV_ATTACK = 0.55f;
static constexpr float ENV_RELEASE = 0.18f;
static constexpr float FLOOR_FALL = 0.12f; // fast follow when quieter
static constexpr float FLOOR_RISE = 0.0008f; // very slow drift upward
static constexpr float FLOOR_MARGIN = 1.25f;
static constexpr float ABS_GATE = 0.0008f;
static constexpr float BALANCE_DEADBAND = 0.06f;
static constexpr float LOUD_MIN_DB = -48.0f;
static constexpr float LOUD_MAX_DB = -6.0f;
static constexpr uint32_t HOLD_MS = 260;
// ES7210 SDP interface 2 / high-pass registers. The LilyGO driver leaves the
// codec in 2-channel I2S mode and the HPF disabled; enable both here.
static const uint8_t ES7210_SDP_INTERFACE2 = 0x12;
static const uint8_t ES7210_ADC34_HPF2 = 0x20;
static const uint8_t ES7210_ADC34_HPF1 = 0x21;
static const uint8_t ES7210_ADC12_HPF1 = 0x22;
static const uint8_t ES7210_ADC12_HPF2 = 0x23;
static bool es7210WriteReg(uint8_t reg, uint8_t value)
{
Wire.beginTransmission(ES7210_ADDR);
Wire.write(reg);
Wire.write(value);
return Wire.endTransmission() == 0;
}
bool SoundDetector::begin(uint32_t sampleRate)
{
if (running_) return true;
sampleRate_ = sampleRate;
audio_hal_codec_config_t cfg = {};
cfg.adc_input = AUDIO_HAL_ADC_INPUT_ALL;
cfg.codec_mode = AUDIO_HAL_CODEC_MODE_ENCODE;
cfg.i2s_iface.mode = AUDIO_HAL_MODE_SLAVE;
cfg.i2s_iface.fmt = AUDIO_HAL_I2S_NORMAL;
cfg.i2s_iface.samples = AUDIO_HAL_16K_SAMPLES;
cfg.i2s_iface.bits = AUDIO_HAL_BIT_LENGTH_16BITS;
esp_err_t err = es7210_adc_init(&Wire, &cfg);
err |= es7210_adc_config_i2s(cfg.codec_mode, &cfg.i2s_iface);
// Put all four ADCs on SDOUT1 as TDM slots. Without 0x02 on this register
// only MIC1/MIC2 reach SDOUT1 and the right microphone is missing.
if (!es7210WriteReg(ES7210_SDP_INTERFACE2, 0x02)) {
Serial.println("ES7210 TDM config failed");
return false;
}
// High-pass the ADC outputs so the detector sees audio, not DC offset.
es7210WriteReg(ES7210_ADC12_HPF2, 0x2a);
es7210WriteReg(ES7210_ADC12_HPF1, 0x0a);
es7210WriteReg(ES7210_ADC34_HPF2, 0x0a);
es7210WriteReg(ES7210_ADC34_HPF1, 0x2a);
// Use the same analog gain on both populated mics so the amplitude
// difference between them is meaningful.
err |= es7210_adc_set_gain(ES7210_INPUT_MIC1, MIC_GAIN);
err |= es7210_adc_set_gain(ES7210_INPUT_MIC3, MIC_GAIN);
err |= es7210_adc_ctrl_state(cfg.codec_mode, AUDIO_HAL_CTRL_START);
if (err != ESP_OK) {
Serial.println("ES7210 init failed");
return false;
}
i2s_config_t i2s = {};
i2s.mode = (i2s_mode_t)(I2S_MODE_MASTER | I2S_MODE_RX);
i2s.sample_rate = sampleRate_;
i2s.bits_per_sample = I2S_BITS_PER_SAMPLE_16BIT;
i2s.channel_format = I2S_CHANNEL_FMT_ALL_LEFT;
i2s.communication_format = I2S_COMM_FORMAT_STAND_I2S;
i2s.intr_alloc_flags = ESP_INTR_FLAG_LEVEL1;
i2s.dma_buf_count = 8;
i2s.dma_buf_len = 64;
i2s.use_apll = false;
i2s.tx_desc_auto_clear = true;
i2s.fixed_mclk = 0;
i2s.mclk_multiple = I2S_MCLK_MULTIPLE_256;
i2s.bits_per_chan = I2S_BITS_PER_CHAN_16BIT;
i2s.chan_mask = (i2s_channel_t)(I2S_TDM_ACTIVE_CH0 | I2S_TDM_ACTIVE_CH1 |
I2S_TDM_ACTIVE_CH2 | I2S_TDM_ACTIVE_CH3);
i2s.total_chan = 4;
if (i2s_driver_install(MIC_I2S_PORT, &i2s, 0, nullptr) != ESP_OK) {
Serial.println("Mic I2S install failed");
return false;
}
i2s_pin_config_t pins = {};
pins.mck_io_num = BOARD_ES7210_MCLK;
pins.bck_io_num = BOARD_ES7210_SCK;
pins.ws_io_num = BOARD_ES7210_LRCK;
pins.data_in_num = BOARD_ES7210_DIN;
pins.data_out_num = I2S_PIN_NO_CHANGE;
i2s_set_pin(MIC_I2S_PORT, &pins);
i2s_zero_dma_buffer(MIC_I2S_PORT);
running_ = true;
if (xTaskCreatePinnedToCore(taskEntry, "sound-detector", 8192, this, 4,
&task_, 0) != pdPASS) {
running_ = false;
i2s_driver_uninstall(MIC_I2S_PORT);
Serial.println("Mic task create failed");
return false;
}
return true;
}
void SoundDetector::taskEntry(void *arg)
{
static_cast<SoundDetector *>(arg)->taskLoop();
}
void SoundDetector::suppress(uint32_t ms)
{
suppressUntil_ = millis() + ms;
}
void SoundDetector::taskLoop()
{
static int16_t block[MIC_BLOCK_FRAMES * MIC_CHANNELS];
for (;;) {
size_t bytesRead = 0;
esp_err_t err = i2s_read(MIC_I2S_PORT, block, sizeof(block), &bytesRead,
portMAX_DELAY);
if (err != ESP_OK || bytesRead == 0) {
vTaskDelay(pdMS_TO_TICKS(10));
continue;
}
size_t frames = bytesRead / (MIC_CHANNELS * sizeof(int16_t));
if (frames == 0) continue;
if ((int32_t)(millis() - suppressUntil_) < 0) {
// Still drain I2S so the DMA doesn't overflow while muted. Drop the
// envelopes too, otherwise the device's own ping would be the first
// thing the detector reports once the mute expires.
envL_ = 0.0f;
envR_ = 0.0f;
publish(0.0f, 0.0f, 0.0f, 0.0f, false);
continue;
}
processBlock(block, frames);
}
}
void SoundDetector::processBlock(const int16_t *frames, size_t frameCount)
{
int64_t sumL = 0, sumR = 0;
int64_t sqL = 0, sqR = 0;
for (size_t i = 0; i < frameCount; i++) {
int32_t l = frames[i * MIC_CHANNELS + MIC_SLOT_LEFT];
int32_t r = frames[i * MIC_CHANNELS + MIC_SLOT_RIGHT];
sumL += l;
sumR += r;
sqL += (int64_t)l * l;
sqR += (int64_t)r * r;
}
float meanL = (float)sumL / (float)frameCount;
float meanR = (float)sumR / (float)frameCount;
float varL = (float)sqL / (float)frameCount - meanL * meanL;
float varR = (float)sqR / (float)frameCount - meanR * meanR;
if (varL < 0.0f) varL = 0.0f;
if (varR < 0.0f) varR = 0.0f;
// Normalise to full scale, then smooth with a fast attack / slow release.
float rmsL = sqrtf(varL) / 32768.0f;
float rmsR = sqrtf(varR) / 32768.0f;
envL_ += (rmsL - envL_) * (rmsL > envL_ ? ENV_ATTACK : ENV_RELEASE);
envR_ += (rmsR - envR_) * (rmsR > envR_ ? ENV_ATTACK : ENV_RELEASE);
// Per-channel noise floor: fall quickly when it gets quieter, creep up very
// slowly so sustained noise does not desensitise the detector.
floorL_ += (envL_ - floorL_) * (envL_ < floorL_ ? FLOOR_FALL : FLOOR_RISE);
floorR_ += (envR_ - floorR_) * (envR_ < floorR_ ? FLOOR_FALL : FLOOR_RISE);
if (floorL_ < 1e-5f) floorL_ = 1e-5f;
if (floorR_ < 1e-5f) floorR_ = 1e-5f;
float sigL = envL_ - floorL_ * FLOOR_MARGIN;
float sigR = envR_ - floorR_ * FLOOR_MARGIN;
if (sigL < 0.0f) sigL = 0.0f;
if (sigR < 0.0f) sigR = 0.0f;
// Adaptive gate: a sound must stand clearly above its channel's floor.
float gateL = fmaxf(floorL_ * 2.0f, ABS_GATE);
float gateR = fmaxf(floorR_ * 2.0f, ABS_GATE);
bool present = (sigL > gateL) || (sigR > gateR);
uint32_t now = millis();
if (present) lastActiveMs_ = now;
bool active = present || (uint32_t)(now - lastActiveMs_) < HOLD_MS;
float total = sigL + sigR;
float balance = 0.0f;
if (total > 1e-6f) {
balance = (sigR - sigL) / total;
if (fabsf(balance) < BALANCE_DEADBAND) {
balance = 0.0f;
} else {
// Remove the deadband and rescale the remaining range to +/-1.
float sign = balance < 0.0f ? -1.0f : 1.0f;
balance = (balance - sign * BALANCE_DEADBAND) / (1.0f - BALANCE_DEADBAND);
}
}
float peak = fmaxf(sigL, sigR);
float db = 20.0f * log10f(peak + 1e-9f);
float loudness = (db - LOUD_MIN_DB) / (LOUD_MAX_DB - LOUD_MIN_DB);
if (loudness < 0.0f) loudness = 0.0f;
if (loudness > 1.0f) loudness = 1.0f;
#if SOUND_DETECTOR_DEBUG
static uint32_t lastPrintMs = 0;
if (active && (uint32_t)(millis() - lastPrintMs) > 250) {
lastPrintMs = millis();
Serial.printf("mic L=%.4f R=%.4f bal=%+.2f loud=%.2f\n",
sigL, sigR, balance, loudness);
}
#endif
publish(sigL, sigR, balance, loudness, active);
}
void SoundDetector::publish(float left, float right, float balance, float loudness,
bool active)
{
portENTER_CRITICAL(&mux_);
reading_.left = left;
reading_.right = right;
reading_.balance = balance;
reading_.loudness = loudness;
reading_.active = active;
portEXIT_CRITICAL(&mux_);
}
SoundReading SoundDetector::read()
{
SoundReading r;
portENTER_CRITICAL(&mux_);
r = reading_;
portEXIT_CRITICAL(&mux_);
return r;
}
+57
View File
@@ -0,0 +1,57 @@
/**
* @file sound_detector.h
* @brief Dual-microphone sound localizer for the T-Deck Plus (ES7210).
*
* Reads the two populated MEMS microphones as a 4-slot TDM stream:
* slot 0 = MIC1 (left), slot 2 = MIC3 (right)
* and exposes a smoothed left/right level, a stereo balance and a loudness
* value suitable for placing a radar blip.
*/
#pragma once
#include <Arduino.h>
#include <driver/i2s.h>
struct SoundReading {
float left; // smoothed level above the noise floor (0..1)
float right; // smoothed level above the noise floor (0..1)
float balance; // -1 = far left, 0 = centre, +1 = far right
float loudness; // 0 = quiet, 1 = loud (dB-mapped)
bool active; // true while a sound is present (with a short hold)
};
class SoundDetector {
public:
// Starts the ES7210 codec and the I2S receive task. Returns false if the
// codec or I2S driver could not be initialised.
bool begin(uint32_t sampleRate = 16000);
// Latest measurement. Safe to call from the main loop.
SoundReading read();
bool available() const { return running_; }
// Ignore microphone input for a while (used so the device's own radar
// ping does not register as a target).
void suppress(uint32_t ms);
private:
static void taskEntry(void *arg);
void taskLoop();
void processBlock(const int16_t *frames, size_t frameCount);
void publish(float left, float right, float balance, float loudness, bool active);
uint32_t sampleRate_ = 16000;
TaskHandle_t task_ = nullptr;
volatile bool running_ = false;
volatile uint32_t suppressUntil_ = 0;
portMUX_TYPE mux_ = portMUX_INITIALIZER_UNLOCKED;
SoundReading reading_ = {};
uint32_t lastActiveMs_ = 0;
float envL_ = 0.0f;
float envR_ = 0.0f;
float floorL_ = 0.01f;
float floorR_ = 0.01f;
};